Esperanto
Shqiptare
Euskara
Zulu
Latinus
Cymraeg
தமிழ்
Slovak
Slovak
Afrikaans
NEWS


Process flow of Poplar Core Film Faced Plywood
Process flow of Poplar Core Film Faced Plywood
2022-02-24 13:59
The process flow of log processing and production of Poplar Core Film Faced Plywood: log → log sawing → wood section cooking → wood section peeling → veneer rotary cutting → veneer drying → veneer finishing → gluing and grouping → pre-pressing → heat Pressing→cutting→cutting→inspecting and grading→packing and storage.

The process flow of veneer processing and production of Poplar Core Film Faced Plywood: veneer finishing → gluing and forming blanks → pre-pressing → hot pressing → cutting → sanding → inspection and grading → packaging and storage.
1. Loss of processing technology: In the entire production process of Poplar Core Film Faced Plywood, log sawing, veneer rotary cutting, veneer drying, veneer finishing, hot pressing, edge trimming, and chopping have an impact on wood loss. For visible losses (with processing residues) and invisible losses (shrinkage and compression). Timber loss is related to factors such as log species, log specifications, equipment conditions, process technology, and finished board specifications.
2. Log sawing: The length of imported logs is generally more than 6 meters. It should be sawed according to the length and quality required by the process. The cut wood should be the length of the finished product of Poplar Core Film Faced Plywood plus the processing allowance. For example, the finished Poplar Core Film Faced Plywood with a width of 1220mmX2440mm, the length of the wood segment is usually 2600mm or 1300mm. The length of the log, the curvature and defects of the log directly affect the yield of Poplar Core Film Faced Plywood, and the waste generated includes small wood segments, truncations and sawdust, etc. The sawing loss rate of logs is generally 3-10%.
3. Veneer rotary cutting: The most widely used veneer in the production of Poplar Core Film Faced Plywood is the veneer produced by rotary cutting method. 8mm or so. The loss of this process is the largest. First, a considerable part of the broken veneer cannot be used due to the out-of-roundness of the wood segment; second, the end loss is caused by the clamping of the rotary cutter on both ends of the wood segment; third, the wood core loss. The waste produced by the veneer peeling is broken veneer and wood core. It can be seen that the loss of veneer peeling is related to the material, diameter and equipment performance of the wood segment, and the loss rate of this part is 15% to 25%.
4. Veneer drying: The moisture content of the veneer after rotary cutting is very high, and the veneer must be dried to meet the requirements of the gluing process. The size of the wood becomes smaller after drying, which is called drying shrinkage. As the moisture content decreases, the length, width and thickness of the veneer will shrink. The shrinkage loss is related to the tree species of the veneer, the moisture content of the veneer and the thickness of the veneer. Dry shrinkage loss rate is generally 4% to 10%.
5. Veneer finishing: Veneer finishing includes cutting, assembling and repairing. Cut the dried strip veneer and piece veneer into specification veneer and splicable veneer, the narrow veneer is spliced into a whole veneer, and the defective whole veneer can be repaired to achieve the process. Quality requirements. The amount of waste veneer generated in this process is related to factors such as the material of the log, the quality of the rotary veneer, the quality of the dry veneer, and the operator's familiarity with the veneer standard, and the loss rate is generally 4% to 16%. The loss rate of the process of directly importing veneer into plywood is generally 2% to 11%.
6. Hot pressing: The slabs that have been coated and assembled are firmly glued together by a certain temperature and a certain pressure. During hot pressing, as the temperature and moisture content of the slab change, the wood is gradually compressed, and the thickness of the slab gradually decreases. This loss is compression loss, which is related to factors such as hot pressing temperature, unit pressure, hot pressing time, tree species and moisture content of Poplar Core Film Faced Plywood. The loss rate is generally 3% to 8%.
7. Trimming: Cut the hot-pressed wool board into specification boards. The amount of trimming waste is related to the processing allowance and the size of the Poplar Core Film Faced Plywood. The larger the size of the Poplar Core Film Faced Plywood, the smaller the trimming loss rate, generally 6% to 9%.
8. Sanding: Sand the surface of Poplar Core Film Faced Plywood to make the surface smooth and beautiful. The waste generated in this process is sanding powder. When the quality of the veneer is good, the sanding amount is small, and the sanding loss rate is generally 2% to 6%.
Poplar,Core,Film,Faced,Plywood
Recommended News
The Growing Demand for Plain HDF: Meeting the Industry's Needs
Time of issue:
2024-10-24 10:20:18
Maximizing Your Supply Chain: The Benefits of Plain Hardboard in Construction and Decoration
Time of issue:
2024-10-23 10:40:53
Polyester Plywood: Blending Tradition and Innovation in Architecture
Time of issue:
2024-10-22 10:20:34

